Q logic/Curtis Cable end

[laoshanren]

Adam,

Sorry to be a pain.

BUT

Can you please confirm that the A1 USB-CANBUS works on the LATER 1314 version.


....................................................

I'll see what I can find up on the error code.

Hi woodygb thanks,

Yes, the #225 is AAM missing, just wonder, my last chair had the same error, I disconnected the AAM and programmed the powerbase, fine, this one there are no parameters in the powerbase.

I try to use later version to connect the chair, and got this:

Best
Adam

[woodygb]

Have you tried cloning the working powerbase and uploading to the defective one ....I doubt that it will work ,but worth a try.

The later 1314 Software is looking for a specific Vid and Pid that identifies approved or genuine Curtis leads...I think from memory that the A1 USB-CAN use a CP2102 Chip .
It MIGHT be possible to rewrite the VID/PID and drivers to make the A1 USB-CAN appear to be a genuine Curtis lead.


A USB device that is plugged in identifies itself by its VID/PID combination. A VID is a 16-bit vendor number (Vendor ID). A PID is a 16-bit product number ...

[laoshanren]

Have you tried cloning the working powerbase and uploading to the defective one ....I doubt that it will work ,but worth a try.

The later 1314 Software is looking for a specific Vid and Pid that identifies approved or genuine Curtis leads...I think from memory that the A1 USB-CAN use a CP2102 Chip .
It MIGHT be possible to rewrite the VID/PID and drivers to make the A1 USB-CAN appear to be a genuine Curtis lead.


A USB device that is plugged in identifies itself by its VID/PID combination. A VID is a 16-bit vendor number (Vendor ID). A PID is a 16-bit product number ...

Hi woodygb thanks

Actually how to clone is what I am looking for, I tried load my last chair's parameters file, it becomes same as the new chair's. do you know how to clone?

the A1 USB-CAN is used a CP2102 Chip. are there any new products?

Best
Adam

[laoshanren]

Have you tried cloning the working powerbase and uploading to the defective one ....I doubt that it will work ,but worth a try.

The later 1314 Software is looking for a specific Vid and Pid that identifies approved or genuine Curtis leads...I think from memory that the A1 USB-CAN use a CP2102 Chip .
It MIGHT be possible to rewrite the VID/PID and drivers to make the A1 USB-CAN appear to be a genuine Curtis lead.


A USB device that is plugged in identifies itself by its VID/PID combination. A VID is a 16-bit vendor number (Vendor ID). A PID is a 16-bit product number ...

Hi woodygb
I found this link, see any thing useful?

http://www.diyelectriccar.com/forums/sh ... 53597.html

Best
Adam

[woodygb]

On page 2 you will find a post from ......ME !

Note ...The Curtis 1309 has been successfully cloned.

[woodygb]

Adam,

The 1314 HELP file contains info on "Cloning".
What version of the earlier 1314 do you have? ...I have build 36 update patch 6...which came with a configuration .ini file that contains this.

[Options]
AdvancedCloningDefault=1

You can find the version info by clicking on Help then About

[laoshanren]

Adam,

The 1314 HELP file contains info on "Cloning".
What version of the earlier 1314 do you have? ...I have build 36 update patch 6...which came with a configuration .ini file that contains this.

[Options]
AdvancedCloningDefault=1

You can find the version info by clicking on Help then About

Hi woodygb thanks

The version I used as picture:

Best Adam

[woodygb]

To enable the Advanced Cloning Option.

Open up the computers registry using regedit ....to do this ...find the Run command and type in regedit.

Search for AdvancedCloningDefault ( It will be under Curtis Instruments -1314 V4 - Settings ) and alter the number from 0 to 1.

Oh! ...please use Woody NOT Woodygb ...the gb is simply added to make the user name "unique" to me and denotes my location...G.B. = Great Britian.

[laoshanren]

To enable the Advanced Cloning Option.

Open up the computers registry using regedit ....to do this ...find the Run command and type in regedit.

Search for AdvancedCloningDefault ( It will be under Curtis Instruments -1314 V4 - Settings ) and alter the number from 0 to 1.

Oh! ...please use Woody NOT Woodygb ...the gb is simply added to make the user name "unique" to me and denotes my location...G.B. = Great Britian.

Hi Woody thank you,

firstly sorry about the name, my poor English knowledge.

I'll find out the par cloning to solve my chair's error now.

Is the final use a USB or RS232 after cloned of 1309 ?

Best
Adam

[woodygb]

The 1309 is a USB-SERIAL interface based on the FTDI chip and not a CAN-USB.

It gets complicated ...but it MIGHT be possible to alter the vid and pid of the A1 CAN-BUS to make it seem like it is one of the approved Curtis interfaces and work with the later 1314 version.

NOTE:- It took 3-4 years to solve the 1309 cable.

[laoshanren]

The 1309 is a USB-SERIAL interface based on the FTDI chip and not a CAN-USB.

It gets complicated ...but it MIGHT be possible to alter the vid and pid of the A1 CAN-BUS to make it seem like it is one of the approved Curtis interfaces and work with the later 1314 version.

NOTE:- It took 3-4 years to solve the 1309 cable.

Hi woody thanks

Am I understand right?
the later version to Q1:
Software + USB-SERIAL interface based on the FTDI chip (and driver)

I found a 1309 USB-SERIAL interface based on FT232RL:

https://www.ebay.ca/itm/FT232RL-3-3V-5- ... SwrklVMjIp

is this one OK?

Best
Adam

[woodygb]

Seems that the regedit option AdvancedCloningOption may only be available in V4 not V3.

Should you wish my version ... SetupExe_OEM_1314-4401_mit_allen_Updates-Bis_31_08_06 .... drop me an EMAIL.

[laoshanren]

Seems that the regedit option AdvancedCloningOption may only be available in V4 not V3.

Should you wish my version ... SetupExe_OEM_1314-4401_mit_allen_Updates-Bis_31_08_06 .... drop me an EMAIL.

Yes Woody thank you.

I changed the AdvancedCloningOption seems no much change.
My email is: GONE -- Burgerman.

Best
Adam

[woodygb]

I have copied your email...
I suggest that you edit your post and remove it IF you can.

[laoshanren]

I have copied your email...
I suggest that you edit your post and remove it IF you can.

Hi Woody,
I don't know how to delete it.
Best
Adam

[woodygb]

Cheers John,

Here's a Magnet / Torrent link for the SetupExe_OEM_1314-4401_mit_allen_Updates-Bis_31_08_06

magnet:?xt=urn:btih:4cc64edf3a6cee5c08f002b7aa1c5c0e9184dbb3

[Burgerman]

I did it already...

[laoshanren]

Seems that the regedit option AdvancedCloningOption may only be available in V4 not V3.

Should you wish my version ... SetupExe_OEM_1314-4401_mit_allen_Updates-Bis_31_08_06 .... drop me an EMAIL.

Yes Woody thank you.

I changed the AdvancedCloningOption seems no much change.
My email is: GONE -- Burgerman.

Best
Adam

Thank you Burgerman.
Best
Adam

[laoshanren]

Cheers John,

Here's a Magnet / Torrent link for the SetupExe_OEM_1314-4401_mit_allen_Updates-Bis_31_08_06

magnet:?xt=urn:btih:4cc64edf3a6cee5c08f002b7aa1c5c0e9184dbb3

Hi Woody,

The "Allow advanced clone" coming at Options menu, I checked it, I don't know how to next, I load the file from one chair, how to transfer to another one?

Best
Adam

[laoshanren]

progress:

My second chair's red LIGHT is gone, the reason of AAM missing is a wrong jumper location, as long as the AAM recognized, simple.
next step, I'll make a remote control joystick to control my project, open to any suggestions please.

I'll attach some pictures next time.

Best
Adam

[woodygb]

Adam,
Open up your Q-logic pod....does it use a JC2000 or MAID Joystick....
The connection should look like this on the Joystick ... 8 pins and use a ribbon to connect the board to the joystick.




If so I already make Android bluetooth or RC controls using an Arduino.

Email me.

[laoshanren]

Adam,
Open up your Q-logic pod....does it use a JC2000 or MAID Joystick....
The connection should look like this on the Joystick ... 8 pins and use a ribbon to connect the board to the joystick.




If so I already make Android bluetooth or RC controls using an Arduino.

Email me.

Hi Woody thanks

I have sent you a email told a little about my project.

I opened one of my joystick, the pictures attached seems not same as your picture?

I can open all my 5 joysticks to check if any one may match, because the remote control is a must for my stuff. Or maybe I can got one same as yours?

Best
Adam

[FelipeOliveira]

Greetings from Brazil, friends!

I would like to know where to get the latest version of software 1314.

Does anyone have the link?

[FelipeOliveira]

Forgive me, wrong question. I'd like the latest version of the cable.

[Burgerman]

I think you must make one.

[FelipeOliveira]

I would really like, but I need guidance would I have the diagram so that I can produce it ??I need Urgent access to a CURTIS 1210

[Mind The Gap]

Hi Woody

Was wondering if you make up the cables for the enable 40 and if so could I have details please.

Writen on control module, Otto bock Part: 2303 Model: 1740-2303 Serial: 6215c, 000847.


Cheers Paul

[woodygb]

I have no experience of the Enable 40 ...but I could make something for you to TRY .

[Mind The Gap]

Hi Woody

Was wondering if you make up the cables for the enable 40 and if so could I have details please.

Writen on control module, Otto bock Part: 2303 Model: 1740-2303 Serial: 6215c, 000847.


Cheers Paul

Hi Woody
Yes please.

Have pm you my address

[Mind The Gap]

Hi woody,

Having any luck. If you need any money or anything let me know.

Cheers paul