Mobility PC Programmer

[bgmen]

Hi!

Where are the settings of the actuator module pilot plus?

[Burgerman]

Inhibit settings are lower down. That's all that can be changed on pilot plus.

[bgmen]

by making changes to the settings on how to save them?

[woodygb]

Lead should be plugged into the joystick.

Controller should be turned ON.

Programming Software should say COMMS ACTIVE

Take a copy of your Configuration and SAVE it as a backup ...call it bgmen1 .


THEN.

Alter the parameters that you wish to modify and they will automatically be altered in the controller.

[Burgerman]

Click save?

[woodygb]

I'm concerned that his pic shows COMMS INACTIVE.

But yes ..click on SAVE.

[woodygb]

PIC.

The SAVE or SAVE AS saves the file on your P.C.

PROG SAVE.png (47.08 KiB) Viewed 15939 times

[bgmen]

then make changes entries include wired and ready

[Burgerman]

You "save" by clicking the upload arrow.
You load your parameters by clicking the other arrow.

Top bar.

[woodygb]

PICS.

Either way is the same.

CONTROL SAVE.png (31.6 KiB) Viewed 15935 times

CONTROL SAVE2.png (18.56 KiB) Viewed 15935 times

[woodygb]

You must have COMMS ACTIVE bottom right corner.

[bgmen]

why after upgrading my turn INHIBIT 2?

[bgmen]

Help!!!!!!!!!!!!!!!!!!!!!!!!!!

[bgmen]

I did as you told me, and I gave it out ok and disconnected the joystick and cable

after 2 min include joystick and was included INHIBIT 2
why so? If you wait 30 minutes will be fine?

[woodygb]

Are you using a translation program? ..If so it's rubbish... as your sentences make little sense.

The picture you posted shows COMMS INACTIVE. ... was it COMMS ACTIVE during programming?

INACTIVE.jpg (132.77 KiB) Viewed 15913 times

[woodygb]

Show a picture of what you are changing.... and the COMMS ACTIVE.

[bgmen]

it in red what to do first?

[bgmen]

Click on the right controller writer began to load and load INHIBID was included

[woodygb]

If it says COMMS INACTIVE it is NOT talking to the controller ..it's only altering a file on your computer.

It MUST say COMMS ACTIVE ..

It will say COMMS ACTIVE when it is talking to the controller.... THEN you can program.

[bgmen]

http://dox.abv.bg/files/listtree here's a picture of changes

[bgmen]

http://dox.abv.bg/files/listtree pic

[woodygb]

We need to tell the Programmer the COMS number.
Open the PGDT Programmer..IGNORE ..the cannot open serial port message.

Click on Tools ..then Comms.

Then pick YOUR leads COMS number.

comms port2.png (219.7 KiB) Viewed 14343 times

[bgmen]

f

жжж.png (92.92 KiB) Viewed 14343 times

[woodygb]

http://dox.abv.bg/files/listtree pic

EMPTY BLANK NOTHING

[bgmen]

I changed the settings of the joystick from 100 to 60

[bgmen]

and the joystick is now blinking and can not move
INHIBID

[woodygb]

OK .. COMMS is ACTIVE.

Upload the program to the controller .
Unplug the lead ..
Turn on/off the joystick ...changes happen straight away ...no waiting.


You can check that the controller has the new settings by READING it again.

[bgmen]

Inhibit 2 Active

[woodygb]

Inhibit 2 Active

And?... you want it as?

[woodygb]

Question.

Is your chair working .... can you drive it?

Is it able to drive but only SLOW?