DWIZ-ADAPT

Power wheelchair board for REAL info!

POWERCHAIR MENU! www.wheelchairdriver.com/powerchair-stuff.htm

Re: DWIZ-ADAPT

Postby woodygb » 22 Aug 2019, 22:23

Not a clue ...sorry.
An expert is a person who has made all the mistakes that can be made in a very narrow field.
Niels Bohr
User avatar
woodygb
 
Posts: 6320
Joined: 12 Mar 2011, 18:45
Location: Bedford UK

Re: DWIZ-ADAPT

Postby Irving » 22 Aug 2019, 22:34

GlennGlenn wrote:Woody
Further to my question about the caps and theie orientation, I think that if a polarised capacitor is used for C1 its +ve must go to ground.
A negative voltage is taken from the Tx terminal (Rx) and stored in C1. The -ve is used for sending RS232 high from Rx rerminal (Tx).
This is a way of level matching the return -ve voltage to the received one irrespective of what shifting and combination is done by the rest of the adaptor before it goes to remote.
I think I should invert C1 before my RS3232 arrives, do you agree?
Glenn

The ground end of c1 should be +ve. C1 and the diode create a TX driven charge pump to provide a -ve reference for the RX circuitry.
C5/6 A (complete)
Puma 40, 75Ah LiFePO4 (pic is on tour @ Whistler, BC)
Puma 40 backup, 73Ah MK (for now)
Spectra Plus (weedy 40Ah MK)
User avatar
Irving
 
Posts: 2114
Joined: 04 Dec 2012, 11:51
Location: NW London

Re: DWIZ-ADAPT

Postby GlennGlenn » 23 Aug 2019, 00:48

Irving
I came to the same conclusion after studying various circuits.
Thanks for the response.
Glenn :thumbup:
GlennGlenn
 
Posts: 17
Joined: 13 Aug 2019, 23:10

Re: DWIZ-ADAPT

Postby kaban » 10 Nov 2019, 20:12

Hi guys, am newbie here. Can anyone PM me a link to the Wiz5 software please?
kaban
 
Posts: 13
Joined: 10 Nov 2019, 20:06
Location: Western Germany

Re: DWIZ-ADAPT

Postby kaban » 19 Apr 2020, 20:54

Hello again,

I've installed Wizard 5 as described by Burgerman.
I don't get Asked for any Password and I can change the user mode (Service etc.).

Then I connected a RS232 to usb converter from the programming Plug to the PC, didn't work out.
Tried it with a CH340, didn't work as well.
With a CP210x it neither worked.

Did I miss something out? :problem:
kaban
 
Posts: 13
Joined: 10 Nov 2019, 20:06
Location: Western Germany

Re: DWIZ-ADAPT

Postby kaban » 19 Apr 2020, 20:55

By the way: I've got a G50 with a DX. Remote has directly got programming port in it, like woody posted somewhere here.
kaban
 
Posts: 13
Joined: 10 Nov 2019, 20:06
Location: Western Germany

Re: DWIZ-ADAPT

Postby kaban » 19 Apr 2020, 21:21

If I send anything to the programming port via a Arduino @ 38400 Baud with SoftwareSerial, I get this answer from Joystick: 1202481281202480 o.O
@ 19200 I get 1020
kaban
 
Posts: 13
Joined: 10 Nov 2019, 20:06
Location: Western Germany

Re: DWIZ-ADAPT

Postby woodygb » 19 Apr 2020, 23:31

kaban wrote:
Then I connected a RS232 to usb converter from the programming Plug to the PC, didn't work out.
Tried it with a CH340, didn't work as well.
With a CP210x it neither worked.

Did I miss something out? :problem:



The 5 pin Hirose port communicates via RS232 SERIAL as opposed to TTL SERIAL.

https://www.sparkfun.com/tutorials/215

Any QUALITY RS232 SERIAL cable ( e.g. one that uses a FTDI Chipset ) should work fine.

E.G. https://www.amazon.co.uk/COOSO-Serial-F ... 172&sr=8-4
An expert is a person who has made all the mistakes that can be made in a very narrow field.
Niels Bohr
User avatar
woodygb
 
Posts: 6320
Joined: 12 Mar 2011, 18:45
Location: Bedford UK

Re: DWIZ-ADAPT

Postby woodygb » 19 Apr 2020, 23:42

DYNAMIC HIROSE.jpg
An expert is a person who has made all the mistakes that can be made in a very narrow field.
Niels Bohr
User avatar
woodygb
 
Posts: 6320
Joined: 12 Mar 2011, 18:45
Location: Bedford UK

Re: DWIZ-ADAPT

Postby kaban » 20 Apr 2020, 08:07

Thank you for the answer.

I think the Problem is in the Software..
Would you send me a PM with all the DL links In need?
kaban
 
Posts: 13
Joined: 10 Nov 2019, 20:06
Location: Western Germany

Re: DWIZ-ADAPT

Postby woodygb » 20 Apr 2020, 08:45

kaban wrote:If I send anything to the programming port via a Arduino @ 38400 Baud with SoftwareSerial, I get this answer from Joystick: 1202481281202480 o.O
@ 19200 I get 1020



All Arduino boards have at least one serial port (also known as a UART or USART), ... Serial communication on pins TX/RX uses TTL logic levels (5V or 3.3V ...


You need RS232 Serial.
An expert is a person who has made all the mistakes that can be made in a very narrow field.
Niels Bohr
User avatar
woodygb
 
Posts: 6320
Joined: 12 Mar 2011, 18:45
Location: Bedford UK

Re: DWIZ-ADAPT

Postby CarbonTech » 26 Apr 2020, 13:08

Hi guys, I am new here. Would someone please PM a link to wizard 5 software?
CarbonTech
 
Posts: 1
Joined: 26 Apr 2020, 12:30
Location: Louisiana, USA

Re: DWIZ-ADAPT

Postby Burgerman » 26 Apr 2020, 16:46

Check PM
User avatar
Burgerman
Site Admin
 
Posts: 54368
Joined: 27 May 2008, 21:24
Location: United Kingdom

Re: DWIZ-ADAPT

Postby Khalid » 16 May 2020, 21:01

Hello everyone ,new member here, hope everyone is doing well, so my neighbor got a mobility scooter which has the rhino dynamic 70 amp controller(ctldc1343/ DS72KSP02) im willing to help him out programming it to his special needs, so i was wondering if you guys would help me get the proper software which i believe needs to be a oem version in order to read and write and making the proper usb cable to plug it to the laptop.
Khalid
 
Posts: 10
Joined: 14 May 2020, 01:00

Re: DWIZ-ADAPT

Postby woodygb » 16 May 2020, 21:10

You need a RS232 ( DB9 )-USB Cable ...I prefer any that uses a FTDI Chip set.

E.G. https://www.amazon.co.uk/DSD-TECH-SH-RS ... B07MYYCMJT

Als0

3 of these........https://www.amazon.co.uk/DSD-TECH-SH-RS ... B07MYYCMJT


Image


and the software.
An expert is a person who has made all the mistakes that can be made in a very narrow field.
Niels Bohr
User avatar
woodygb
 
Posts: 6320
Joined: 12 Mar 2011, 18:45
Location: Bedford UK

Re: DWIZ-ADAPT

Postby Khalid » 16 May 2020, 21:37

Thank you woody for the fast reply and for the pm! ,so what i understand is that i just need this usb rs232 cable connecting just those 3 pins tx dx and gnd to the controller and it will read on the laptop? No special dongles or anything?
Khalid
 
Posts: 10
Joined: 14 May 2020, 01:00

Re: DWIZ-ADAPT

Postby Khalid » 16 May 2020, 21:44

Also i was wondering if i connect everything i just have to turn on the scooter with the key right? not adding any other power wire to the programming connector like pg drives do. Would these boards im gunna attach might work instead of this cable by any chance, because i already i have them
Attachments
Screenshot_20200514-232414_Samsung Internet.jpg
Khalid
 
Posts: 10
Joined: 14 May 2020, 01:00

Re: DWIZ-ADAPT

Postby Khalid » 16 May 2020, 21:45

And this
Attachments
Screenshot_20200514-232329_Samsung Internet.jpg
Khalid
 
Posts: 10
Joined: 14 May 2020, 01:00

Re: DWIZ-ADAPT

Postby Irving » 16 May 2020, 21:51

Khalid wrote:Also i was wondering if i connect everything i just have to turn on the scooter with the key right? not adding any other power wire to the programming connector like pg drives do. Would these boards im gunna attach might work instead of this cable by any chance, because i already i have them


You can probably make that work...
C5/6 A (complete)
Puma 40, 75Ah LiFePO4 (pic is on tour @ Whistler, BC)
Puma 40 backup, 73Ah MK (for now)
Spectra Plus (weedy 40Ah MK)
User avatar
Irving
 
Posts: 2114
Joined: 04 Dec 2012, 11:51
Location: NW London

Re: DWIZ-ADAPT

Postby LROBBINS » 16 May 2020, 22:44

Dynamic systems normally require a dongle for programming, but there's a workaround that can get you into an OEM-plus mode without one. When you're ready to go, ask here and someone will PM you with the information you'd need. The software itself is downloadable from the Dynamic web site.
LROBBINS
 
Posts: 4980
Joined: 27 Aug 2010, 09:36
Location: Siena, Italy

Re: DWIZ-ADAPT

Postby woodygb » 16 May 2020, 23:10

Khalid wrote:Also i was wondering if i connect everything i just have to turn on the scooter with the key right? not adding any other power wire to the programming connector like pg drives do. Would these boards im gunna attach might work instead of this cable by any chance, because i already i have them


As Irving say's ... yes it should.

Just remember that the connection convention is TX of one board goes to the RX of the other .
An expert is a person who has made all the mistakes that can be made in a very narrow field.
Niels Bohr
User avatar
woodygb
 
Posts: 6320
Joined: 12 Mar 2011, 18:45
Location: Bedford UK

Re: DWIZ-ADAPT

Postby Khalid » 16 May 2020, 23:18

Thanks for the help ,will try and see what happens
Khalid
 
Posts: 10
Joined: 14 May 2020, 01:00

Re: DWIZ-ADAPT

Postby Khalid » 21 May 2020, 12:00

Hey woody so i did everything as told but cant get the controller to connect to the laptop, i used this board i will attach a pic, and i have the oem program, i have the solo d50529/1 ,tried changing the com ports didnt work just this time i didnt get the cant open serial port message but still said comms inactive, used a 47 k resistor and a 1n4148 zener, what can be the problem?
Khalid
 
Posts: 10
Joined: 14 May 2020, 01:00

Re: DWIZ-ADAPT

Postby Khalid » 21 May 2020, 12:08

Khalid
 
Posts: 10
Joined: 14 May 2020, 01:00

Re: DWIZ-ADAPT

Postby woodygb » 21 May 2020, 13:41

Your going to confuse things by posting your Solo question in this Dwiz Adapt thread.

I will move/copy your question to where you had previously posted it.
An expert is a person who has made all the mistakes that can be made in a very narrow field.
Niels Bohr
User avatar
woodygb
 
Posts: 6320
Joined: 12 Mar 2011, 18:45
Location: Bedford UK

Re: DWIZ-ADAPT

Postby cata300 » 29 May 2020, 20:11

Hello guys, I am new here.
Could someone please PM me with a link to the Wizard 5 software?
Thanks!
cata300
 
Posts: 2
Joined: 10 Jul 2019, 06:34

Re: DWIZ-ADAPT

Postby Burgerman » 30 May 2020, 08:58

Did you find it?
User avatar
Burgerman
Site Admin
 
Posts: 54368
Joined: 27 May 2008, 21:24
Location: United Kingdom

Re: DWIZ-ADAPT

Postby woodygb » 30 May 2020, 08:58

Yup
An expert is a person who has made all the mistakes that can be made in a very narrow field.
Niels Bohr
User avatar
woodygb
 
Posts: 6320
Joined: 12 Mar 2011, 18:45
Location: Bedford UK

Re: DWIZ-ADAPT

Postby cata300 » 31 May 2020, 20:35

It works.
Thanks a lot for the instructions!
cata300
 
Posts: 2
Joined: 10 Jul 2019, 06:34

Re: DWIZ-ADAPT

Postby znachor8 » 22 Jun 2020, 15:18

Hi guys, I am new here. I use Storm 4 every day, I would like to try to improve some parameters. Would someone please PM a link to wizard 5 software?
znachor8
 
Posts: 2
Joined: 22 Jun 2020, 15:05

PreviousNext

Return to Everything Powerchair

Who is online

Users browsing this forum: Bubbernator, Burgerman, DirtinLa, Heygnow, Jay_x, Roadrunner, Rollin Positive, rover220, Yennek and 42 guests

 

  eXTReMe Tracker