Quickie Groove Brushless TT build.

[elryko1992]

Ok thanks, maybe you found the thread.

[hank]

When finished tweeking to get how i like it
will then strip down all bits for powdercoating.
Going for all matt/satin black look or may have white frame.

[shirley_hkg]

NEED 10" rims for TT GB to go tubeless .

Saw this , and it's a good 14" tubeless candidate for GB , without losing torque .

[Burgerman]

Too thin. He likes the fat tyres, smoother ride, less sinking...

[hank]

Not for me shirley_hkg
but thanks

[Burgerman]

Ends up 14.3 diameter. almost 4 wide. But very little sidewall.

[hank]

DSC05034.JPG (92.36 KiB) Viewed 13058 times

Is there any way to disable freewheel levers on brushless motors
as one of mine has broke off level with casing
they are very brittle hollow plastic.

Could they be disabled with wiring or will have to remove lever arm part
inside casings first.

[hank]

Wanted to blank them off with a cover plate if possible.

[shirley_hkg]

YES , you can avoid the inhabit by just shorting that blue micro switch .

Another thing worth noting is the plastic linkage will get displaced after a dozen clicks of the solenoid . That will render you an ineffective parking brake .

I'll hot glue it .

[hank]

I'll hot glue it .

I take it you mean glue the broken part back together.
shirley

[shirley_hkg]

Is there any way to disable freewheel levers on brushless motors
as one of mine has broke off level with casing
they are very brittle hollow plastic.

Could they be disabled with wiring or will have to remove lever arm part
inside casings first.

NO, I mean you should find a way to prevent the plastic part from rotating (change to free wheel position by itself).

It is supposed to be held in place with a spring load linkage , but it is broken now .

[hank]

Shirley
Got you.
What i have done is made a alloy flat plate to cover over
casting hole area fixed on the original 4 screws.
put the lever in drive mode then cut the white freewheel
lever level to top face then covered with plate.
The lever cant move now.
Just lost freewheel access now.

[hank]

New backrest fitted with custom made alloy posts.
waiting for black etch primer for posts

[Burgerman]

How about a larger pic from further away so we can see the chair? Several angles. Is this lithium yet?

And are you interested is spare motors, controller, lighting module, cables, unused rem550, etc? All with no broken plastic parts.

[hank]

PM me prices and details.
Will get more pics over weekend John.
Still lead slabs till dead

[hank]

Latest picture of build
Power Wheelies easy

[Burgerman]

Very good. Basically a salsa. The reason you dont get brushless issues I did is because you are smaller and so lighter than me judging by the seating.

[hank]

Thanks I am about 11 stone.
Happy with it apart from colour
Ordered some etch black and 2k clear coat for alloy parts.
Waiting for wide arm pads and setting joystick to my liking.
End plugs to fit in alloy box where i lifted battery box for more clearance.
and fit some in frame where holes show.
New cushion next as well.
General tidy up a few tweeks then,getting there slowly.

[rover220]

looking good.

[Burgerman]

Not that it matters at our speeds, but the rear tyres are reversed.

Right way. The tread pattern is designed to clear water towards the outer edges as you hit it at high speed. So no aquaplaning at speed. Wont make a blind bit of difference on a powrchair! But evey motorcyclist will spot it...

[hank]

Left them to catch your hawk eye John
Will change over when i strip to paint.
I noticed the first time i fitted them on the chair.
But didnt like the idea of the spacers dropping out of wheel halfs.

[hank]

looking good.

Thanks Rover 220

[hank]

Altered joystick position
Made a flat plate need lifting higher

[Burgerman]

brightened

[elryko1992]

Hank put some photos with your BM3 Clone to see please!

[hank]

Look here old bm3 picture elryko 1992
viewtopic.php?f=2&t=6032

[Burgerman]

Thats a BM 2.5. Lead, 24V, rather than 45V lithium/roboteq 16mph. A cross breed!

[hank]

BM 2.5 not 3 sorry

[elryko1992]

Nice! Maybe i will found a F55 or 155E to make a BM3 is the same i think no? Burgerman?

[hank]

brightened

Joystick position set right now.
Jay fusion cushion added