Where to find PGDT programmer software

[Mechanic Bob]

I found the software thank you.

[sabain]

Reaching out here for help.
Same as others before im looking for oem copy of the software to program my
PG Drives Technology S drive controllers

Cheers,
sabain

[Joachim1]

Hello people,
my name is Joachim and I come from Germany. I have a luxury problem. I'm currently building an older meyra allraund 900c with a pg pilot + control system into a chain-driven lawn mower. Since the speed backwards and the steerincontrol is too slow / damped, I wanted to have this corrected by a wheelchair service near me. Unfortunately he does not have the equipment to do this. Therefore I try this way. The cable should not be a problem due to the information here in the forum, but I would still lack the corresponding pc software. Can someone help me with that?

Many Greetings
Joachim

[Burgerman]

See PM.
Sabain too...

[Joachim1]

Thank you.
Regards
Joachim

[sabain]

Thanks.

Regards
Sabain

[patrick]

Hello,

same as sabain and Joachim1 - I'm looking for a oem copy of the software for programming a PG Drives Technology S drive controller.

Greetings
Patrick

[woodygb]

You have a P.M.

The link say's VR2 ...do not worry ... the software is fine for the S-drive

[patrick]

Thank you and greetings from Austria.

Patrick

[frankenfir]

Im looking for oem pgdt s drive pc software right now i have a delaer level 14.6.0. Appreciate if someone her could help.

[woodygb]

Check your P.M.

[cheeseball]

Hi, hoping someone can point me in the direction of the oem s-drive software, thanks.

Cb

[cc17926]

Good morning from the soggy east coast US..

I have replaced the S-Drive in my wife's scooter (the D51270 model) . Can I please have a copy of the OEM programming software used to update the settings on the replacement controller board?

Thank you!!

[woodygb]

You have a P.M.

[jk-tech]

Hello,
i*m also looking for the software, can anybody help me?
Many thanks
br
Jens

[aroli12]

Hi Everybody!

My name is Roland and I live in Hungary.

I have a mobility scooter with S-Drive controller and I going to replacing the motor with a larger one. I would like to change the S-Drive parameters, but I have only Dealer version.

Could somebody give me a higher version of Mobility PC Programmer?

Thank you for your help!
Roland

[woodygb]

The only parameter that you might need to change is the motor compensation value.

[aroli12]

Thank you very much. I will check this parameter.

[leon112233]

Thanks - worked perfectly first time!

When I first saw the version without a diode, it seemed a bit odd that you could tie two tx pins together (the one from the cable, and the combined one on the controller) - unless they're designed to be used this way (which the cable very likely isn't, since it has separate rx and tx lines), they tend to fight each other, and not work. Having a diode makes much more sense.

Some details, if it helps confirm what does/doesn't work:
Cable: http://www.ebay.com/itm/121153158397
Diode: 1N4148, just because I have a pile of them.
Plug: Random XLR from my parts stash
Driver: Latest from prolific's website for XP, 2.1.44.226
Controller: 50A VSI.
Software: http://filebin.ca/qeVD8PXcQ5p/oem_programmer.zip
Total assembly time around ten minutes, most of which was finding parts.

There's still some lag, but it's much, much better. I need to try playing with the compensation and some of the other settings. The biggest problem is it takes too much stick movement to make a slight steering correction start, and seems to decelerate both motors, not just the one it should be slowing down to effect the turn. Some logic to prevent you from getting sideways, I think.

Thanks again,
--Bushytails

I'm working on a bumper car with the drivetrain of a mobility scooter, however we would like to program some things, the mobility scooter uses a Penny and Giles controller.

Could someone provide me with an active download link regarding the software?

Thanks!

[Santimismo]

Hi woody, i need to find the SW to get conected to a sunrise salsa M2. Could you help me¿?

The ECU is a VR2 Quickie.

BR

[Burgerman]

See PM

[taycong]

Hello everyone, im a young guy from China, im making a go kart for my little son, and its driven by a chinese version PG motor controller, it comes with a wig-wag type throttle, i wanna change it into a one ending type ,like a car peddle one, so i think i need the programming software, can anybody help me , thanks a lot.

[woodygb]

Check your messages

[taycong]

Thanks a lot ,sir, wish u have a good one

[cikig36186]

Hi, i need a software to connect with VR2, can you provide it to me?
Thanks a lot!

[Avia Mobility]

1) I too am looking for the OEM software for PGDT. The links here are all dead with "bandwidth exceeded". Can anyone help me locate the OEM version - or anything above the dealer version?

2) I am trying to reprogram a bunch of Invacare "SHARK" controllers so they will accept the generic DK-REMD01 joysticks. Has anyone had experience with this?

[henkserious]

Hi,

Can anybody help me with the oem version? Many thanks in advance.

Greetings,

Jan

[woodygb]

Check your messages

[Zelkin]

Hi

I need help

We have a car with S-Drive converted as an electric car for my nephews.
Unfortunately, the car now drives in the wrong direction and the brake settings should also be changed.
Can someone send me the appropriate software and tell me what I need for the 4Pin Molex cable
I have built a FTDI TTL adapter and the cable with diode and 47kohm resistor.
Is that enough?

Thanks for the help

Greetings

[woodygb]

Swap over the motor connections and the car will go in the other direction.

The brake on the end of the motor is just a PARKING BRAKE.

Cable diagram.

viewtopic.php?f=2&t=5523&start=180#p169035

Check your messages .