Mobility PC Programmer

[bgmen]

j.png (64.97 KiB) Viewed 10392 times

these 2 settings how many percent has to be? FOR 80am

[Burgerman]

That wont affect you. Leave as it is, or increase to 20 seconds. And leave the percentage alone.

[peterik]

allround 970 ortopedia It can be used Mobility PC Programmer setting

[peterik]

allround 970 ortopedia It can be used Mobility PC Programmer setting

Does anyone have experience with this program vozikom

[Burgerman]

Don't understand the question?

[peterik]

What do the symbol?

[peterik]

I joined 2 daughters rx and tx on the chair and was only responding now I can not find the right program on my chair alloround970 meyra

[diimon]

Hi,
Can any help with soft pc mobility programmer?
Thanks

[woodygb]

check your messages.

[diimon]

What mean trip code 1E05? Wheelchair not run, system VSI
Thanks

[woodygb]

https://support.pgdt.com/Online-Diagnos ... abase.aspx


1E05 - VR2 PM & VSI - Inhibit 3 (On-board Charger) Active
This occurs when the controller detects that Inhibit 3 input is active. The Inhibit 3 input is via the 3 way on-board charger (OBC) and is normally associated with this function. The operation of Inhibit 3 will depend upon the programmed settings of the controller and the wheelchair on which it is being used.

Check all wiring, switches and OBC (if fitted) connected to Inhibit 3.

If the trip still persists then the Controller must be assumed to be defective.

[kirkreiten]

Hi,

I hope I post this right.

I lost my programming cable for my 180A S Drive -- Diode thing didn't work.. rigged 2 MOSFETs on the FTDI's Tx, and an OpAmp on the Rx The S Drive wasn't pulling low enough.

Anyway, my Comm looks great... Reads the S Drive great. Writes

However, I'm getting some unsupported parameters -- i don't recall those before. Do I ignore them?

Thx

Kirk

[Burgerman]

Yes. You have no option. Theres many firmwares...

[kirkreiten]

Thx

[Polo Giovanni]

Have a nice day, some one can give me some help.
this is what i read when i access the card with the program i have.
I have to read the Serial Number and type number. how can I do? it is a type of setting or another program.
thank you

[Burgerman]

Dont know about scooters. But also dont understand what it is you are asking?

[woodygb]

Comms Active ... Click on the RED Down arrow.

[woodygb]

YOU DO NOT WANT THIS DEFAULT PROGRAM.NO NO NO

[Polo Giovanni]

I need to read this data, my program does not read it.

[woodygb]

[woodygb]

I need to read this data, my program does not read it.

OK ... We may have a language barrier.

You have tried to read the 45 Amp S-Drive controller and all you get is the controller type D50676.08 and the controller serial number BJ18061579 ?

How old is the controller and has someone been trying to program it ? ...I ask because D50676.08 is a VR2 controller not an S-Drive!!!

[woodygb]

VR2 CONTROLLER

https://www.ebay.co.uk/itm/185077372793

https://www.ebay.co.uk/itm/334185940979

[woodygb]

Try this....

STEP 1

COMMS ACTIVE

CLICK ON CHECKSUM CORRECTION

Now TURN OFF the Controller.

STEP 2

TURN ON THE CONTROLLER

COMMS ACTIVE

CLICK FILE

SELECT

NEW S-DRIVE TEMPLATE

UPLOAD THE NEW S-DRIVE TEMPLATE.

TURN OFF THE CONTROLLER

THEN RETRY.

[woodygb]

I suppose that I should have asked for a picture of your controller as you have not said what it is ... I assumed that it was an S-Drive but it suddenly occurs to me that it might be a VR2 that someone has over written with an S-Drive template ... in that case you should use a NEW VR2 TEMPLATE in STEP 2.

[Polo Giovanni]

Sorry but maybe I don't express myself well, I don't speak English very well.
The card is an s-driver.
with my program, when I read the data I don't see the two boxes with.
look.

[woodygb]

The card is an s-driver.
with my program, when I read the data I don't see the two boxes with.
look.

Your screen shots show conflicting information.


Which of these controllers ( cards )????

S-Drive



VR2

[woodygb]

Your screenshot shows a mismatch in controller types.

I suspect that your controller has been programmed with the wrong type.

I suspect that your controller IS a VR2 ...but it has been programmed as an S-Drive.

Thus the software is looking for the VR2 parameters and cannot find them as they do not exist in the expected format.

[Polo Giovanni]

My driver is

[Polo Giovanni]

the photograph I sent you, I found it on the internet. is an example.
I have the s-drive but I cannot read, with my program, the serial numbers of the s-drive

[Polo Giovanni]

I think I have the wrong program, which does not read the serial number