Where to find PGDT programmer software

[woodygb]

Check your message inbox.

[DougL]

I just received the Yamaha programmer cable and also having a tough time finding the programming software for the Pride Mobility GC2 and VR2 controllers.

[mp3-king]

Hi, i am from Germany (sorry for my english)
I have a Scooter with a PG Solo and sarch a Programming Software to change the settings.
I hope everyone can help me...

your mp3-king

[woodygb]

The Mobility software will "talk" to the SOLO...but WILL NOT PROGRAM the SOLO controller....

solo comms.jpg (92.44 KiB) Viewed 15575 times

You need a handheld programmer SP1 OEM version or the Industrial software.

[mp3-king]

Where I can find the Industrial software?

[steves1977uk]

Thats the £64,000 question

I imagine the industrial pc programming software is almost impossible to get as it's hard enough trying to buy the mobility version.

Steve

[mp3-king]

Thank you for your quick response

mp3-king

[markusb]

Hi guys,

I have a chairman with a pilot + system that Im trying to use for a project.
I was trying to find the programming software for the power module but bandwidth exceeded it said. Is there any updated link to the software?

I dont know if this is the right board for this other question, but I'll ask away
The chair is fully functioning except it does not move! Brakes does not release, wheels do not turn.
Seat actuators, lights and so on works. I get no error flash on the bar graph display, but if I disconnect a brake or a motor it registers a fault and makes a flashing pattern.. It just does not move when pulling the stick.
Is there more inhibits than the cable from the manual brake release? Or what can cause this problem for me?

Thanks in advance!

[Burgerman]

There can be more inhibits, or reversed ones. All can be cancelled in programming.

Check PM

[rlnguy]

I am assuming by chairman, you mean Permobil Chairman?
On Permobil Chairman, the most common reason for a drive inhibit is the connection to the freewheel lever switch. Just in front of the right motor (as sitting in the chair), there is a small black connector. If you follow the wires back from the switch, it's easy to find. It is very easy to pull the wires just enough, when putting new batteries in, for example, to unplug this connector. I've had that call, probably a hundred times.
You have to remove a few covers to access it, but that's where I would start.
depending on configuration, it could also be inhibited because the seat is raised (or thinks it is). There could be other possible, as well.
hope this helps

[markusb]

I found the problem.. The two control boxes for the actuators was mixed with the boxes from another chair. I swapped them, and checked all inhibits I could find in the schematic.
Now it runs fine!

[lakonas]

Hi guys,
I'm looking for the mobility scooter programming software for the S-Drive (D51446.06).
Thanks in advance!

[phoenix]

Hello,
I'm also looking for the OEM PC Programmer for the S-Drive controllers. Can someone help?

[woodygb]

It may appear in your Inbox.

[Ben]

Hi,
I am looking for the programming software for pgdt s drive controller.
Can someone help ?
Thanks

[Burgerman]

Does the usual mobility programmer not include this? it may help to pm woodygb if not.

[Ben]

Thanks Burgerman and Woodygb,
I found it and I will proceed with the assembly of my own programming cable now !

[phoenix]

Can someone help me get a recent manufacturing version (Level C) of the software? I'm looking for version 14 or later.
I do have an older version but it doesn't read some controllers.

[baravantan]

Hi,
I'm looking for the OEM version of the PC Programmer for the EGIS/SDrive controllers. Can someone help me?
Thanks

[Ben]

Thanks again Burgerman and Woodygb,
I build a cable wkth a FTDI USB and It work...

[PaulieTheKid]

Hi,

I'm looking for the PC mobility programmer programming software for the Penny & Giles model EGIS 110 controller.
Does anybody know where to find it, or can somebody hook me up?

Thanks,
Paul

[c500user]

I do not know if this is of help to anyone, but I came across a download link at the US Permobil site. The R-Net software seems to install fine on my Win7 PC, but I have no dongle so cannot connect to my C500.

http://www.permobilus.com/software.php

[rover220]

I do not know if this is of help to anyone, but I came across a download link at the US Permobil site. The R-Net software seems to install fine on my Win7 PC, but I have no dongle so cannot connect to my C500.

http://www.permobilus.com/software.php

Only dealer level unfortunately.

[c500user]

I do not know if this is of help to anyone, but I came across a download link at the US Permobil site. The R-Net software seems to install fine on my Win7 PC, but I have no dongle so cannot connect to my C500.

http://www.permobilus.com/software.php

Only dealer level unfortunately.

How easy is it to get hold of a dongle? I would not mind starting with a dealer version to see if I can get the chair to behave itself.

[Burgerman]

OEM software is easy...
Dongle isnt! Well at least an OEM one isnt easy to get.

[c500user]

But how hard is it to get a dealer dongle?

[Burgerman]

Anyone can buy one. Dealer = end user, same thing. You can even find someone WITH an OEM version and let him reprogram your R-net to have DEALER level On Board Programming built in. Or rather enabled. Since its already in there!

[c500user]

Then I need to find someone to do that for me in Holland!

[Burgerman]

Yes.

[somsak]

Hi all,
My wheelchair is breakdown. When I push joystick forward left side reverse and right side is forward. when pull joystick back left side forward and right side reverse. I suspect VR2 controller got a problem. Where I can get a pc programmer software. Realy need help. Thanks