Brushless eBay!!! Bought.

[Vitolds]

+roboteq

[Burgerman]

Vitolds, see pm.

[Vitolds]

[Vitolds]

+
https://ru.aliexpress.com/item/Nema34-M ... aceddb61f9

[Vitolds]

1:10 = 500 PM
BIG WEIGHT
8kg + 6 Nema kg

[Vitolds]

http://www.macmotortech.com/escooter-motor.html

PMSM

[Burgerman]

But no good for powerchair.

[Vitolds]

[Vitolds]

only sport

[shirley_hkg]

Uk ebay has quite some nice chairs . Looking forward to come across a nice TTplus Xplore .

Hay, you guys please keep an eye on it for me too .

[Burgerman]

There was one about 2k recently.

[Burgerman]

Now have a totally mint shiny REM 550.

https://dynamiccontrols.com/en/download ... sue-2/file

[hank]

Turn up the volume
Have fun programming you new stuff.

[Burgerman]

Just spoke to a tech guy at Dynamic. He told be all DX-GB power modules are basically the same as long as they are all the 4 pin DX BUS connectors no matter what the extra designations or names used. Inc all the mk4, 5, 6i are all the same (just fancy invacare designations) but may have different firmware that limits some options in settings, and that they don't store a copy of the memory setting. Battery connectors, cable lengths, motor connectors vary by part numbers. The programmer sees them all as DX-GB.

All the motors are 3rd party, and now invacare only as a source, and they have just been significantly redesigned for a 40 percent torque increase over the 2nd versions. Called plus... Also improved efficiency. You cant buy brushless controllers from dynamic any more but they do make them soley for dynamic (unofficially) and thats also now the only source. And DX bus joystick can be programmed to work them from C versions and upwards. UK, EU, US all the same.

[hank]

Interesting read John.
Nice to know on what models will and wont program.

[Vitolds]

you can say what you will do with this invacare?

[Burgerman]

Shirley, can you get these cheaper too?

http://www.j-mart.biz/j-parts/index.php ... ts_id=3707

I need ONE wheel G-craft 8 x 5.5J plain and...
One x wheel G-Craft 8 x 4J plain.

Each wheel gives me a left and right half rim.
So making the brushless motor wheel rim 8 x 4.25 wide and 3.25 wide.
One for W I D E stretched 120/70 tyres, one for 110/80 on the xplore chair.

And with both motor/rim sealed should be OK tubeless.

[shirley_hkg]

Will try ..

[Burgerman]

Thanks!

Not symetrical... So will need 2 rims!

http://www.gm-moto.jp/item/mky-00121/

Maybe they have the flat ones no holes that I need.

[shirley_hkg]

No fruitful result .

3.5j for 8 inch / 4.5j for 10 inch .


I guess my mechanics can lathe one from a aluminum block , estimated £50 for one half .

[Burgerman]

The metal will cost 5x that!

[shirley_hkg]

No, it is cheap here , even 6061 grade .

Will get a close estimation , after the Luner NY holiday , if you are interested .

[Burgerman]

Sounds good! May as well have holes in the right places!

[shirley_hkg]

Alternately , cut this apart , and put an extra ring section to extend to your desired width . Weld them together , lathe the slot for rubber seal, and redo the finishing .

That may be even better and costs less .

This costs £12.00 a rim .

Wait till you received the 8” rims and confirm them fit for modification .

[Burgerman]

It wont. The center well, too deep... No room for bolts. Unless I drill 5 new holes in the rotor...

[Burgerman]

My motors arrived. They look almost new. Barely even dusty. Better than the pictures!
And my refurb (absolutely brand new if you ask me!) REM 550 joystick is here already.
Power module also here. Cables quite short but easy to make an extended one if needed. Also looks like new. Do people actually use these chairs?

And I won this http://www.ebay.co.uk/itm/Invacare-ACS- ... fresh=true

Because I need a spare and because I am going to fit one of woodys RC interfaces so I can RC my brushless invacare chairs... Can just leave a spare buss cable where its easy to connect if when needed.

And I need a couple of wheel rim halfs for the brushless to measure and test...

[shirley_hkg]

After setting them up , REMEMBER to calibrate motors first , before running them , even unloaded .

[shirley_hkg]

And I need a couple of wheel rim halfs for the brushless to measure and test...

I'd have thrown in a pair , if I had known it earlier .

Ask him . He always has stock .
http://m.ebay.com/itm/Invacare-Control- ... Ciid%253A7

[Burgerman]

72 dollars shipping alone for a power module! Buying in the US also always means customs rip off charges and vat on top...

Can you possibly post me a couple with cheap Chinese postal service?

[shirley_hkg]

Will find the pair that I set aside .