Q logic/Curtis Cable end

[woodygb]

Adam,
Open up your Q-logic pod....does it use a JC2000 or MAID Joystick....
The connection should look like this on the Joystick ... 8 pins and use a ribbon to connect the board to the joystick.




If so I already make Android bluetooth or RC controls using an Arduino.

Email me.

[laoshanren]

Adam,
Open up your Q-logic pod....does it use a JC2000 or MAID Joystick....
The connection should look like this on the Joystick ... 8 pins and use a ribbon to connect the board to the joystick.




If so I already make Android bluetooth or RC controls using an Arduino.

Email me.

Hi Woody thanks

I have sent you a email told a little about my project.

I opened one of my joystick, the pictures attached seems not same as your picture?

I can open all my 5 joysticks to check if any one may match, because the remote control is a must for my stuff. Or maybe I can got one same as yours?

Best
Adam

[FelipeOliveira]

Greetings from Brazil, friends!

I would like to know where to get the latest version of software 1314.

Does anyone have the link?

[FelipeOliveira]

Forgive me, wrong question. I'd like the latest version of the cable.

[Burgerman]

I think you must make one.

[FelipeOliveira]

I would really like, but I need guidance would I have the diagram so that I can produce it ??I need Urgent access to a CURTIS 1210

[Mind The Gap]

Hi Woody

Was wondering if you make up the cables for the enable 40 and if so could I have details please.

Writen on control module, Otto bock Part: 2303 Model: 1740-2303 Serial: 6215c, 000847.


Cheers Paul

[woodygb]

I have no experience of the Enable 40 ...but I could make something for you to TRY .

[Mind The Gap]

Hi Woody

Was wondering if you make up the cables for the enable 40 and if so could I have details please.

Writen on control module, Otto bock Part: 2303 Model: 1740-2303 Serial: 6215c, 000847.


Cheers Paul

Hi Woody
Yes please.

Have pm you my address

[Mind The Gap]

Hi woody,

Having any luck. If you need any money or anything let me know.

Cheers paul

[woodygb]

I can only provide an interface with JUST 3 wires.... the connection to your socket will be down to you.

[Mind The Gap]

I can only provide an interface with JUST 3 wires.... the connection to your socket will be down to you.

Hi Woody
Have built main Lifepo4 pack and addon pack, reprogramed vr2 controllers with your help but this thread is a bit beyound me.

Was wondering if I brought the chair to someone, they could reprogram it for me. Dont mind the drive.

Thanks for your time Woody.

Cheers Paul

[Burgerman]

If you cant make the connector. Open the case, fit a small 3 pin connector by cutting one of these 2s balance cables in half. Solder one half to the charge connector in the joystick. And the other to your programming cable. When you want to program you need to remove screws to get to the connector.

[Mind The Gap]

Hi woody

Just seen pic in Q-logic programming interface that has given me a better understanding.
So if you could carry on doing what you was doing and will see how I get on.

Thanks bm

Cheers Paul

[rover220]

I can only provide an interface with JUST 3 wires.... the connection to your socket will be down to you.

Hi Woody
Have built main Lifepo4 pack and addon pack, reprogramed vr2 controllers with your help but this thread is a bit beyound me.

Was wondering if I brought the chair to someone, they could reprogram it for me. Dont mind the drive.

Thanks for your time Woody.

Cheers Paul

happy to program if you come to me

[Mind The Gap]

I can only provide an interface with JUST 3 wires.... the connection to your socket will be down to you.

Hi Woody
Have built main Lifepo4 pack and addon pack, reprogramed vr2 controllers with your help but this thread is a bit beyound me.

Was wondering if I brought the chair to someone, they could reprogram it for me. Dont mind the drive.

Thanks for your time Woody.

Cheers Paul

happy to program if you come to me

Hi Rover220

Will try to make cable first, but if that fails will take you up on offer after the 10 August when car goes in for service.

Cheers Paul

[Mind The Gap]

If you cant make the connector. Open the case, fit a small 3 pin connector by cutting one of these 2s balance cables in half. Solder one half to the charge connector in the joystick. And the other to your programming cable. When you want to program you need to remove screws to get to the connector.

Hi bm sent link to some cables I have, the two prong one I have filed down so they now fit in joystick socket.
Have sent picture link this way as kept getting error message about couldn't determine size.


https://www.flickr.com/gp/62550310@N08/5NZ493

[Burgerman]

Sorry, not a clue. Dont know which pin does what.

[Mind The Gap]

I can only provide an interface with JUST 3 wires.... the connection to your socket will be down to you.

Hi Woody
Have built main Lifepo4 pack and addon pack, reprogramed vr2 controllers with your help but this thread is a bit beyound me.

Was wondering if I brought the chair to someone, they could reprogram it for me. Dont mind the drive.

Thanks for your time Woody.

Cheers Paul

happy to program if you come to me

Hi Rover220

Sons available and said he could run me up to you on Sunday if that's ok.
And just so we are clear on things, it a 5 pin enable 40 joystick and controller.
Apologies to Woody and BM for wasting their time, this is a safer route for me before I short out the whole lot.

Thanks Paul

[woodygb]

No problem Paul.

I had previously wondered if the 50 of the part number / code was an indication of the model and it is now confirmed that it is indeed an indication of the powerbase type.

So we now have more definitive info on what lead / comms protocol is used by certain Pride/Curtis models.

The Curtis EnAble40 LOOKS the same as a Pride/Curtis CTLDC1552 or 1750-2009 and the EnAble40 manual suggests serial type comms ( RX / TX ).

It is however a variant of the EnAble50 and uses CAN.

A Curtis 1740 powerbase is an EnAble40 and a 1750 is an EnAble50 ...the 40 is programmed with a serial type lead and the other 50 uses CAN.

I am assuming that if the control system is an NE model that it is an EnAble40.... a check of the powerbase number should confirm this.

[woodygb]

EnAble40

CTLDC1552 ...LOOKS the same as the EnAble40 but is an EnAble50 variant.

EnAble50

[Mind The Gap]

Hi Woody

Have made 5 pin connector that fits socket. Have pictures but cant seem to upload them only 65 kb.
The label on the module reads as follows.

Otto bock
Part 2303
Model 1740-2303
Serial 6215C.000847

Cheers Paul

[woodygb]

1740 is the number for an EnAble40....which should program via a Serial type cable using RX and TX.

Did Rover sort you out?

[Mind The Gap]

Hi Woody
Worked out the picture problem up loading 2 pictures .

Cheers Paul

[Mind The Gap]

1740 is the number for an EnAble40....which should program via a Serial type cable using RX and TX.

Did Rover sort you out?

No. Will have to try to make cable.
Have a look at pics and see what you think. Fits in nice and firm.

Cheers paul

[woodygb]

I have a cable here that is ready for you to solder to that plug if you want to try it.

[Mind The Gap]

I have a cable here that is ready for you to solder to that plug if you want to try it.

yes please woody.

[woodygb]

P.M. me your address again ...the price is £20 via Paypal ...refundable if you get no joy.

[Mind The Gap]

P.M. me your address again ...the price is £20 via Paypal ...refundable if you get no joy.

Hi Woody

Send paypal details please.

Cheers Paul

[Mind The Gap]

Thanks Woody everything is working fine.

Cheers Paul